Boat Plans For A Chesapeake Deadrise
Ok, intrepid reader! Sailing season is soon upon us! Before you know it I will be sailing around in my Goat Island Skiff and rocking house, and maybe you will feel that kick in your pants to get outside and do some adventuring of your own!
As presented in my earlier post, I have some repairs that require my attention. One of them is cosmetic by nature, and thats the pesky buckled buttstrap joints on my sides. This buckledness was born from my inadequate gluing job many moons ago in my garage when my Goat was but an infant in many different pieces. That being said, I am attempting to make correct this blemish. I have posted this picture before, but here it is again:
 |
| Note joint |
Boo buckled buttstrap joint.
I have been advised by Mik Storer (Goat Island Skiff designer you should know that by now) that the best way to tackle this issue is through the use of a "Payson Joint" which basically entails fairing the buckled portion, digging a trench to lay down some fiberglass tape and epoxy, and then sanding smooth and repainting. A Payson Joint is a way to join two pieces of plywood together, and usually the trench and fiberglass tape are used on both sides of the joint. It is a flexible, strong, and cosmetically innocuous way to join two pieces of ply together, since the tape lies in the trench that was hollowed out and doesnt bump up and out and sticks out. It is strong, like bull, joint repair technique.
My repair only needed it done on one side, since I have a buttstrap on the inside of the joint.
First, I needed to sand away the paint from the bumped areas:
 |
| Starboard, note ghetto torture sanding board! |
 |
| Port |
Youll notice that on the port side I already have done some work, this was last spring before I painted. I noticed the buckling before I applied the paint and I just ground it flat with my ROS and painted it. It was suitable, but not ideal by any means. The starboard side didnt show up until halfway through the season.
After the ridge was faired smooth it was time to "dig the trench" that would accept the fiberglass tape. Here is the Starboard side trenched out. The trench should not be more than a veneer, but after the fairing the first veneer was almost gone anyway, so it didnt take much to get down to the next layer. The glue between veneers offered a good guideline too, visually offering the trench as opposed to feeling it out with my fingers.
 | |||
| Starboard trenched |
After the trenches were dug it was time to apply the fiberglass tape and thickened epoxy. These would fill the trench and make everything smooth and fair.
 |
| Port side with fiberglass tape in trench |
After this whole shebang cured, I have it a light sand to see if I had any hollows or ridges.
 |
| Starboard |
 |
| Port |
Obviously, I needed to do some filling, so QUICK FAIR TO THE RESCUE!
 |
| Starboard |
After the Quick Fair set, I sanded it down until I got back to the epoxy. Everything seemed smooth as a babys bottom, so tonight I applied the first coat of primer.
This is the real test, the paint, because ones fingers can only feel so much, but glossy paint will show every flaw in your boat for the world to see! Ugh.
My port side came out as good as it was going to come out. I am pleased with the results. My starboard side, ever my nemesis, came out almost just right, except on the bottom of the tape on the aft side. Theres a little ridge there than didnt get filled. I mean, I have to be looking to see it. My lovely wife basically told me to forget it. My enabler told me to fix it.
 |
| Starboard |
 |
| Also Starboard |
Now please take note that this imperfection is actually almost impossible to see in any real world scenario. I have to shine the flashlight "just so" to see it plainly. On the water or on the trailer, no one will ever pick this up, I actually have to move about a bit in the garage to see it under normal light.
But I know its there. Its going to bug me, I did all this work, Im going to have to fix it. Its only one coat of primer that is meant to be sanded off anyway. UGH. So close.
My only fear is that I screw it up worse!
Oh, I also put in a plug in my daggerboard:
Check out the leaves that finally coming out! WOOT!
Do you find information about Boat Plans For A Chesapeake Deadrise are you looking for? If not, below may help you find more information about the Boat Plans For A Chesapeake Deadrise. Thank you for visiting, have a great day.
0 komentar:
Posting Komentar